MWO 9-2320-280-35-2
(16) Position existing cable stowage cleat to holes drilled in step (14) and secure with two existing
screws, washers, and M45913/4-4CG8Z nuts as shown in figure 54.
(17) Position two MS21333-75 clamps on VPC cable and secure clamps to holes drilled in step (15)
using two MS51958-63 screws and 271169 nuts as shown in figure 54.
k. FRONT SEATBELT ASSEMBLY INSTALLATION.
(1) Position 12340058 washer and anchor mount (part of seatbelt assembly 12480530) to bracket on
left side body and "B" pillar and secure with 12340259-6 bolt as shown in figure 55. Tighten bolt to 35-40
lb-ft (48-54 Nm).
(2) Install retractor (part of seatbelt assembly 12480530) to bracket assembly (12342372) on left "B"
pillar and secure with 2436164 washer and 454970 screw as shown in figure 55. Tighten screw to 35-40
lb-ft (48-54 Nm).
(3) Position 12342381 bracket, 12341856 washer, and "D" ring (part of seatbelt assembly 12480530)
to left "B" pillar. Secure with 12340259-4 bolt and 12342722 reinforcement as shown in figure 55. Tighten
bolt to 35-40 lb-ft (48-54 Nm).
(4) Position 12340058 washer and anchor mount (part of seatbelt assembly 12480530) to bracket on
right side of body and "B" pillar and secure with 12340259-6 bolt as shown in figure 55. Tighten bolt to
35-40 lb-ft (48-54 Nm).
(5) Install retractor (part of seatbelt assembly 12480530) to bracket assembly (12342372) on right
"B" pillar and secure with 2436164 washer and 454970 screw as shown in figure 55. Tighten screw to 35-
40 lb-ft (48-54 Nm).
(6) Position 12342381 bracket, 12341856 washer, and "D" ring (part of seatbelt assembly 12480530)
to right "B" pillar. Secure with 12340259-4 bolt and 12342722 reinforcement as shown in figure 55.
Tighten bolt to 35-40 lb-ft (48-55 Nm).
l. "B" PILLAR COVER PADDING ASSEMBLY INSTALLATION.
(1) Position existing left "B" pillar cover to mount holes on "B" pillar and roof. Secure bottom section
of "B" pillar cover to "B" pillar with two MS27183-11 washers and MS35206-298 screws as shown in
(2) Install MS27183-11 washer and MS35206-298 screw in mount holes on top rear section of roof
(3) Position 12446739 padding assembly to top section of left "B" pillar cover and aline mount holes
(4) Position three 2436161 washers, and B1821BH025C075N bolts in mount holes on padding
assembly and left "B" pillar cover. Install three 2436161 washers and 9419454 nuts as shown in figure 57.
Do not tighten bolts and nuts.
(5) Install MS27183-11 washer and MS35206-298 screw in mount holes on padding assembly and left
front section of roof as shown in figure 57. Tighten screw to 120 lb-in. (13 Nm).
(6) Tighten bolts and nuts installed in step (4) to 120 lb-in. (13 Nm).
(7) Install 12340103-4 and 12340103-3 edge trim pieces on front and rear sections of left "B" pillar
Change 2