REPLACE ENGINE OIL FILTER ASSEMBLY (M548A3) Continued - TM-9-2350-247-20-1_779

Google+

Facebook

LinkedIn

Twitter

Digg

StumbleUpon

REPLACE ENGINE OIL FILTER ASSEMBLY (M548A3) Continued - TM-9-2350-247-20-1_778

INDEX Subject WP Sequence No.-Page No. 7.62 mm machine gun mount Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0515 00-1 A Accelerator linkage M548A3 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0200 00-1 Access cover Front (M548A3), removal/installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0391 00-1 Hull bottom, replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0383 00-1 Seal, power plant right rear, replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0389 00-1 Top (M548A1), removal/installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0390 00-1 Access covers Fuel compartment Removal/installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0163 00-1 Adapter NBC M3 heater (M548A3), replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0532 00-1 Adjusting linkage Generator drive belts (M548A1), replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0243 00-1 (M548A3), replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0247 00-1 Air box drain and crankcase breather collector can Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0134 00-1 Air box drain check valve and tubes M548A3 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0136 00-1 Air box drain tubes M548A1 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0135 00-1 Air box heater M548A1 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0189 00-1 Switch, replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0260 00-1 Air box heater electrode M548A3 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0188 00-1 Air box heater harness and igniter cable M548A1 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0182 00-1 Air box heater harness and ignition cable M548A3 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0183 00-1 Air box heater hoses, tubes, and fittings 1

TM-9-2350-247-20-1 Crane (CAB) Components Recovery Vehicle Full Tracked: light Armored M578 (2360-00-439-6242) (EIC:3LA) Manual
Page Navigation
665

TM 9-2350-247-20-1 REPLACE ENGINE OIL FILTER ASSEMBLY (M548A3) — Continued 0146 00 INSTALLATION 1. Apply sealing compound primer and a thin even coat of sealing compound to cleaned external threads of elbow (1) and elbow (2) before installing. 2. Install oil filter assembly (3) on bracket (4) with four screws (5), new lock nuts (6), and eight washers (7). 3. Install bushing (8) and AOAP sampling valve (9) on oil filter assembly (3). 4. Install elbow (1) and elbow (2) on oil filter assembly (3). 5. Connect oil inlet hose (10) to elbow (1). 6. Connect oil outlet hose (11) on elbow (2). 7. Start engine (see your -10). Check oil filter assembly (3) for leaks. 8. Stop engine (see your -10). Wait about 20 minutes for oil to drain back to pan. Then check oil level. Add oil if needed (WP 0128 00). FOLLOW-THROUGH STEPS 1. Connect both battery negative leads (WP 0292 00). 2. Lower center seat (see your -10) END OF TASK 0146 00-3/4 blank

Western Governors University

Privacy Statement
Press Release
Contact

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business